If your AutoJeweler RGB Flow Series LED emblem is not turning on, is flickering, displaying incorrect colors, or is not responding to the controller/app, complete the troubleshooting steps below before submitting a warranty request. Important: Many R

<p>If your AutoJeweler RGB Flow Series LED emblem is not turning on, is flickering, displaying incorrect colors, or is not responding to the controller/app, complete the troubleshooting steps below before submitting a warranty request.</p><p><strong>Important:</strong> Many RGB Flow Series issues are caused by power, ground, wiring, connectors, controller setup, or Bluetooth communication rather than the LED emblem itself.</p><hr><h2 id="1-check-power--ground">1. Check Power &amp; Ground</h2><p>Start by confirming that the controller is receiving proper power and ground. Insufficient power or a weak ground can cause flickering, dim lighting, incorrect output, or complete loss of operation. :contentReference[oaicite:1]{index=1}</p><ul><li>Verify the positive power connection is secure.</li><li>Verify the ground connection is secure.</li><li>Ground to clean, bare metal whenever possible.</li><li>Avoid painted, coated, loose, or corroded grounding points.</li><li>Inspect the inline fuse and replace it if blown.</li><li>Check power and ground wiring for cuts, pinches, loose terminals, or damage.</li></ul><p>If you have a multimeter, verify that the controller is receiving the proper automotive power specified for your product.</p><hr><h2 id="2-inspect-all-wiring--connectors">2. Inspect All Wiring &amp; Connectors</h2><p>Loose connections, damaged wiring, or poor pin contact can prevent the system from working correctly and can also cause missing colors. :contentReference[oaicite:2]{index=2}</p><p>Inspect all connections between the power source, controller, and LED emblem.</p><ul><li>Make sure every connector is fully seated.</li><li>Inspect connector pins for bending, damage, or poor contact.</li><li>Check for loose or recessed pins.</li><li>Inspect wiring for cuts, pinches, or exposed conductors.</li><li>Check connectors for moisture, corrosion, or debris.</li><li>Make sure waterproof connectors are properly tightened where applicable.</li></ul><p>Disconnect power before unplugging or reconnecting wiring.</p><hr><h2 id="3-power-cycle-the-controller">3. Power-Cycle the Controller</h2><p>Resetting the controller can resolve temporary controller or Bluetooth communication issues. ORACLE recommends disconnecting controller power for approximately 10 seconds before reconnecting it. :contentReference[oaicite:3]{index=3}</p><ol><li>Disconnect power from the controller.</li><li>Wait approximately 10&#x2013;15 seconds.</li><li>Reconnect power.</li><li>Reopen the controller app.</li><li>Test the lighting again.</li></ol><hr><h2 id="4-check-bluetooth--the-controller-app">4. Check Bluetooth &amp; the Controller App</h2><p>If the controller has power but will not connect or respond through the app:</p><ul><li>Make sure Bluetooth is enabled on your phone.</li><li>Make sure you are using the correct app for your controller.</li><li>Close the app completely and reopen it.</li><li>Turn Bluetooth off and back on.</li><li>Power-cycle the controller.</li><li>Move your phone closer to the controller.</li><li>Make sure the app has the permissions required by your phone.</li><li>Update the app and your phone software if updates are available.</li><li>If necessary, reinstall the controller app.</li></ul><p>Some Android-based controller apps may also require Location/GPS permissions for Bluetooth device discovery. :contentReference[oaicite:4]{index=4}</p><p><strong>Note:</strong> Many RGB controllers are detected and connected from inside their designated app rather than through the phone&apos;s standard Bluetooth pairing menu.</p><hr><h2 id="5-test-basic-lighting-output">5. Test Basic Lighting Output</h2><p>Once the controller connects, test basic solid colors before testing animated Flow Series effects.</p><p>Test:</p><ul><li>Solid Red</li><li>Solid Green</li><li>Solid Blue</li><li>Solid White, if supported by your product/controller</li><li>Several Flow Series/color-chasing effects</li></ul><p>If one specific color is missing, inspect the wiring and connector pins carefully. Poor pin contact can cause individual color channels to stop working. :contentReference[oaicite:5]{index=5}</p><hr><h2 id="6-if-the-emblem-flickers-dims-or-displays-dim-red">6. If the Emblem Flickers, Dims, or Displays Dim Red</h2><p>Flickering, dim output, or dim red lighting is commonly associated with insufficient power or a poor ground connection. :contentReference[oaicite:6]{index=6}</p><ul><li>Recheck the positive power connection.</li><li>Recheck the ground connection.</li><li>Confirm the ground is on clean bare metal.</li><li>Check the inline fuse and fuse holder.</li><li>Inspect all controller terminals and connectors.</li><li>Try another known-good grounding point if necessary.</li></ul><hr><h2 id="7-if-the-controller-connects-but-the-emblem-does-not-light">7. If the Controller Connects but the Emblem Does Not Light</h2><p>A controller successfully connecting to your phone confirms that it is receiving power and that its Bluetooth communication is functioning. It does <strong>not</strong> necessarily confirm that the controller&apos;s LED output is functioning correctly.</p><p>If the controller connects but the emblem remains off:</p><ul><li>Make sure the lighting is switched ON in the app.</li><li>Increase the brightness level.</li><li>Try a basic solid-color mode.</li><li>Inspect the controller-to-emblem connection.</li><li>Inspect connector pins and wiring.</li><li>Power-cycle the controller and retest.</li></ul><hr><h2 id="8-test-with-a-known-good-compatible-controller">8. Test With a Known-Good Compatible Controller</h2><p>If another compatible Flow Series controller is available, testing with it can help determine whether the controller or LED emblem is causing the problem.</p><p><strong>If the emblem works with the known-good controller:</strong><br>The original controller is likely the source of the problem.</p><p><strong>If the emblem still does not work:</strong><br>Continue inspecting the emblem wiring, connectors, and LED assembly.</p><p><strong>Important:</strong> Only use a controller that is known to be compatible with your specific lighting type. Flow Series/color-chasing products should only be used with compatible Flow Series/color-chasing controllers. :contentReference[oaicite:7]{index=7}</p><hr><h2 id="9-inspect-for-physical-damage-or-moisture">9. Inspect for Physical Damage or Moisture</h2><p>Inspect the complete system for signs of damage.</p><ul><li>Cut or pinched wiring</li><li>Broken or damaged connectors</li><li>Bent or recessed connector pins</li><li>Loose wires</li><li>Corrosion</li><li>Moisture inside connectors or components</li><li>Burn marks, melted wiring, or signs of overheating</li></ul><p>Visible wiring damage or blown inline fuses should be addressed before continuing troubleshooting. :contentReference[oaicite:8]{index=8}</p><hr><h2 id="quick-symptom-guide">Quick Symptom Guide</h2><table style="width:100%; border-collapse:collapse;"><thead><tr><th style="border:1px solid #ddd; padding:10px; text-align:left;">Symptom</th><th style="border:1px solid #ddd; padding:10px; text-align:left;">Check First</th></tr></thead><tbody><tr><td style="border:1px solid #ddd; padding:10px;">Nothing powers on</td><td style="border:1px solid #ddd; padding:10px;">Power, ground, inline fuse</td></tr><tr><td style="border:1px solid #ddd; padding:10px;">Controller will not connect</td><td style="border:1px solid #ddd; padding:10px;">Power, Bluetooth, correct app, permissions</td></tr><tr><td style="border:1px solid #ddd; padding:10px;">Controller connects but emblem stays off</td><td style="border:1px solid #ddd; padding:10px;">Controller output, connectors, wiring, emblem</td></tr><tr><td style="border:1px solid #ddd; padding:10px;">Flickering or dim output</td><td style="border:1px solid #ddd; padding:10px;">Power and ground</td></tr><tr><td style="border:1px solid #ddd; padding:10px;">One color is missing</td><td style="border:1px solid #ddd; padding:10px;">Connector pins and wiring</td></tr><tr><td style="border:1px solid #ddd; padding:10px;">Incorrect colors/effects</td><td style="border:1px solid #ddd; padding:10px;">Connections, controller/app settings</td></tr></tbody></table><p><br></p><hr><h2 id="still-having-trouble">Still Having Trouble?</h2><p>If the issue remains after completing the troubleshooting steps above, submit an <strong>AutoJeweler Warranty &amp; Return Request</strong>.</p><p>Please be prepared to provide:</p><ul><li>Your order number</li><li>Product name</li><li>A detailed description of the problem</li><li>Photos of the wiring and connections</li><li>A short video showing the issue</li><li>Which troubleshooting steps were completed</li><li>Whether the controller appears and connects in the app</li><li>Power/voltage test results when applicable</li></ul><p>This information helps AutoJeweler determine whether the issue is related to the power connection, controller, wiring, connectors, or LED emblem and allows us to provide the correct warranty solution faster.</p><p><strong>Do not return or discard the emblem, controller, wiring, or other included components unless instructed by AutoJeweler.</strong></p><p>Submitting a warranty request does not automatically authorize a refund, return, or replacement. Additional troubleshooting, photos/video, or return instructions may be required before a warranty resolution is approved.</p>

RGB Flow Series LED Emblem Troubleshooting Guide

Fast Support. Real Solutions. Start a chat with one of our support agents during normal business hours

Didn't find what you need? Send a support ticket and one of our support agents will reply within 24 hours.

Main Site

TikTok

Youtube

Submit a Request

Sign in

AutoJeweler

Troubleshoot AutoJeweler LED emblems, Flow Series lighting, controllers, wiring, power issues, Bluetooth connections, and common lighting problems.

LED Emblem Troubleshooting & Controller Help | AutoJeweler

Diagnose common issues with LED emblems, controllers, power, wiring, Bluetooth connections, colors, and lighting output.