AutoJeweler logo
AutoJeweler logo

All articles

12V RGB Flow Series Emblem Installation Guide – Hybrid ControllerUpdated 17 days ago

This guide applies to current AutoJeweler 12V RGB Flow Series grille emblems that use a Bluetooth-capable controller and, on hybrid-controller kits, an included handheld RF remote.

Important: AutoJeweler Flow Series kits do not all use the same power harness. Your exact kit may include an inline-fused battery harness, fuse-tap harness, plug-and-play adapter, or another product-specific connection. Follow the wiring supplied with your exact product first.

1. Test the Complete Kit Before Installation

Before mounting the emblem, connect the emblem, controller, and supplied harness together and verify that the system powers on.

  • Confirm all illuminated sections operate.
  • Test Bluetooth/app control when included.
  • Test the handheld RF remote when included.
  • Do not permanently mount the emblem until the complete kit has passed this test.

2. Confirm Fitment and Mounting Location

  • Compare the emblem dimensions with the available grille space.
  • Check clearance behind the grille for mounting hardware and wiring.
  • Make sure the emblem and wiring will not interfere with active grille shutters, cameras, sensors, supports, cooling components, belts, or fans.
  • Test-fit before drilling, trimming, or modifying the grille.

3. Mount the Emblem

Position the emblem level and centered in the desired location. Use the mounting hardware supplied with your exact kit. Do not overtighten acrylic components or pull on the wire where it exits the emblem.

4. Route the Wiring

  • Route the emblem wiring through the grille into the engine compartment.
  • Keep wiring away from exhaust components, high heat, sharp edges, belts, fans, hinges, and other moving parts.
  • Do not permanently secure all wiring until the system has been tested again.

5. Connect the Controller

  1. Connect the emblem to the output side of the supplied controller.
  2. Connect the controller to the supplied power harness.
  3. Align keyed plugs correctly and seat them fully.

Do not force connectors. If a plug does not align naturally, verify that you are connecting the correct components.

6. Connect Power and Ground

Use the power method supplied with your kit.

  • Inline-fused battery harness: Connect according to the supplied harness instructions and keep the included fuse in place.
  • Fuse-tap harness: Use a suitable 12V circuit and follow the AutoJeweler Fuse Tap guide for fuse selection and orientation.
  • Ground: Use a clean, secure factory ground, clean unpainted chassis point, or battery negative when appropriate for the supplied harness.

How to Use a Fuse Tap for AutoJeweler LED Emblems & Accessories →

7. Bluetooth / App Setup

  • Power the lighting system before searching for the controller.
  • Enable Bluetooth on your phone.
  • Use the app specified for the controller included with your kit.
  • Connect to the controller from inside the designated app when required.
  • Test solid colors, brightness, speed, and several Flow Series effects.

8. RF Remote Setup

If your kit includes a handheld RF remote, test the remote after the controller has power. Use it to verify basic color, brightness, speed, and effect control. If the Bluetooth app works but the remote does not, verify the remote battery and controller pairing/instructions for that kit.

9. Final Test Before Reassembly

  • Turn the system on and test all lighting functions.
  • Confirm the controller and all connectors remain secure.
  • Confirm the wiring cannot contact hot or moving components.
  • Secure loose wiring with zip ties.
  • Reinstall removed grille/trim components only after the lighting system passes the final test.

Need Help?

If the emblem does not operate correctly, use the RGB Flow Series LED Emblem Troubleshooting Guide.

For additional support, send AutoJeweler your order number, vehicle year/make/model/trim, product name, clear photos of the power and ground connections, photos of all controller/emblem plugs, and a short video showing the issue.

Was this article helpful?